- POOL CLEANERS/PARTS
- WATER TESTING
- PALINTEST LUMISO POOLTEST EXPERT PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST 6 PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST 3 PHOTOMETER AND REAGENTS
- PALINTEST POOLTEST 10 PREMIER PHOTOMETER AND REAGENTS
- PALINTEST POOLTEST 25 PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST PHOTOMETERS
- PALINTEST DRINKING WATER, WASTE WASTER AND PROCESS WATER TESTING
- PALINTEST COOL POOLTESTER AND REAGENTS
- PALINTEST COMPARATOR KITS
- PALINTEST POOLTESTER KITS
- PALINTEST TEST STRIPS
- AUTOMATION/ SENSORS
- CHEMICALS
- CHLORINE GENERATORS
- PUMPS & FILTERS
- FILTER CARTRIDGES
- TOOLS & ACCESSORIES
- CHEMICAL FEEDERS
- POOL LIGHTS
- POOL COVERS
- ALARMS
- ALADDIN PRODUCTS
ULTRAMAX PARTS
Sort by:Recommended
12. P-Clip (5/8", Coated Steel)
Used to fasten the insulated part of a 4, 7 or 9-wire cable to the Handle Assembly.12. P-Clip (11/16", Stainless Steel)
Used to fasten the foam-insulated part of a 9-wire cable to the Handle Assembly.12. P-Clip (11/16", Plastic)
Used to fasten the foam-insulated part of a 9-wire cable to the Handle Assembly. (We suggest the stainless steel P-Clip)13., 74. or 81. Screw (#8, 11/16", Phil Pan-Flat Head.
Used to attach the side plate to the body assembly. On the T4, used to fasten the clamps around the DC pump to the Plate Block. On the T2, used to fasten drive motor to the body assembly.
15. Plug (9-pin, Female, 9-wire)
Used on Ultramax Jr. and Ultramax. Always unplug unit before working on electrical system!26. Body Assembly - Ultramax
White with Holes, Lock Tabs, Outlet Ring and Inserts. This is only 1/2 the unit. 2 required for Ultramax.27., 62. Screw (8-18, 3/4", Phil No-Head
Used to fasten the Pump Motor to the Outlet Bottom Ring on the Body Assembly.30. or 74. Lock-Nuts Set of 8
Hex, Nylon Insert. For fastening the screws of the Anti-Roll Brackets. On the T4, used to attach screws of the Clamp and attach it to the Sideplate.
45. Sideplate
Blue, 6 holes, 4 for bolts, 2 for motor access. For AB Plus RC, AB Ultra, AMAX, AMAX Biturbo, Ultramax JR, UMAX50. Screw
Bolts. Extra-Long. For use with the Ultramax. To fasten bodies together through center sideplates.56. Stepped Sleeve Roller
Beige Supports Drive Belts, installs on the upper Sideplate leg. In 2004, Aqua Products switched to the Beige Stepped Sleeve Roller, which is slightly thicker than the white ones. This change helps the belts stay tighter, which helps prevent abnormal wear. If you have an older unit we suggest upgrading to the beige rollers. Each unit has 2 #56. Stepped Sleeve Rollers.
57. Drive Belts (per pair)
Tan belts. If you are changes your drive belts, we also suggest replacing your #51-Bushings and inspect your #58-Drive Pulley for wear. Any wear in these items can cause slack in your drive belts and reduce their longevity. We also suggest installing a belt tensioner device to take up any slack in your belts.
60. Pump Motor
For the Aquabot Plus RC, AB Ultra, Aquamax Jr. Plus, Aquamax, Aquamax B-Turbo, Ultramax Jr. and Ultramax. Pump motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.80. Drive Motor (MASTER, black)
For Ultramax and Ultramax Jr. Drive motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.80. Drive Motor (MASTER, Black, BB Air Sensor)
For Ultramax and Ultramax Jr. Drive motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.83. Spiral Pin
3/4" long stainless steel. Used in the end of the Drive Motor shaft, use Lok-Tite when installing.
97. Brushes (Blue Molded Rubber)(Pair)
This is the standard brush and can be used on all types of pools.97. Brushes (Light Blue PVA Foam)(Pair)
The PVA foam brushes last longer than the standard brushes, but are more expensive. The PVA foam brushes have more traction when compared to the standard brush so the unit travels faster and will climb the walls higher (floats may have to be adjusted if changing from molded rubber brushes). The PVA brushes are more difficult to install and detailed instructions will need to be followed. You can find these instructions on our "Do-it-Yourself" page of this website.99. Drive Track with Traction Tabs (Blue)
Used for all Model "G" units. Must use spacer brackets for RC and T4 units.101. Filter Bag (Mesh)(Leaf Bag)
This filter bag is used when there are a lot of leaves in the pool. It has larger holes in the bag that allow the unit to suck up larger debris without restricting the flow. Fits all residential Aquabot and Watertech units104. Screw (#6, 11/16", Phil Pan-Flat Head, Pointed)
Used to fasten the 5300/5301 Filter Screen to the Body Assembly.
112. Fuse Holder
Standard, push and turn style. Always unplug unit before working on electrical system!
114. Lighted Switch (For most power supplies)
Standard Red, 3-wire. Always unplug unit before working on electrical system.
119. OUTDOOR TIMER
8-hour, Programmable, GFCI - Used to regulate cleaner's run time when it does not have an auto shut-off.Ultrakart
Steel Construction, fits power supply, cable and unit. Fits any unit. We prefer this unit to the Buggy because it is much better built.Foam Climbing Rings (Set of 4)
Light Blue PVA (1" thick) The climbing rings slide over the standard brushes and give the unit more traction for climbing slick surfaces.Connector (Sky Blue Plastic)
Used to make "Y" connection in the Nylon Rope Assembly on the cable. (We suggest the Stainless Steel Version)