- POOL CLEANERS/PARTS
- WATER TESTING
- PALINTEST LUMISO POOLTEST EXPERT PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST 6 PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST 3 PHOTOMETER AND REAGENTS
- PALINTEST POOLTEST 10 PREMIER PHOTOMETER AND REAGENTS
- PALINTEST POOLTEST 25 PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST PHOTOMETERS
- PALINTEST DRINKING WATER, WASTE WASTER AND PROCESS WATER TESTING
- PALINTEST COOL POOLTESTER AND REAGENTS
- PALINTEST COMPARATOR KITS
- PALINTEST POOLTESTER KITS
- PALINTEST TEST STRIPS
- AUTOMATION/ SENSORS
- CHEMICALS
- CHLORINE GENERATORS
- PUMPS & FILTERS
- FILTER CARTRIDGES
- TOOLS & ACCESSORIES
- CHEMICAL FEEDERS
- POOL LIGHTS
- POOL COVERS
- ALARMS
- ALADDIN PRODUCTS
REMOTE CONTROL PARTS
:
from
to
Sort by:Recommended
10., 73. or 81. Screw (Pan head)
(#8, 11/16", Phil Pan-Flat Head) For fastening the Drive Motor through the Handle Bracket. or For fastening all White Drive Motors or Black Drive motors with a spacer bracket. On the T4 used to fasten the back plate block to the body, insert from outside of body assembly.
30. or 74. Lock-Nuts Set of 8
Hex, Nylon Insert. For fastening the screws of the Anti-Roll Brackets. On the T4, used to attach screws of the Clamp and attach it to the Sideplate.
66. Tubing per foot
Tubing (Clear, 5/16" IDx7/16" OD, from Air Filter to DC Pump) for Aquabot Turbo Solo and Remote Control.67. SPACER BLOCK
Grey, Stepped Shape. Used to position the Piston apart from the Model G Drive Tracks.70. Clamp
Grey plastic, narrow used to fasten the DC Pump to Back Plate.Used on Aquabot Turbo Solo, Aquabot Turbo RC, Aquabot T4 and all Aquamax RC/Solo Units.70. Clamp Bracket
Grey Plastic, wide, used to fasten piston to the sideplate. Used on Aquabot Turbo Solo, Aquabot Turbo RC and all Aquamax RC/Solo Units.
71. Back Plate Block
Grey plastic, 4 holes used to support DC pump inside of unit.Used on Aquabot Turbo Solo, Aquabot Turbo RC, Aquabot T4 and all Aquamax RC/Solo Units.72. Spacer
Plastic, cylinder used between Plate Block and Body Assembly. Used on Aquabot Turbo Solo, Aquabot Turbo RC, AquabotT4 and all Aquamax RC/Solo Units.
73. Screw (10-32, 1-3/4" Phil Pan Head)
Used to fasten Clamp & Piston on the Sideplate of a standard unit.
73. Screw (10-32, 1-3/4" Phil Pan Head)
Used to fasten Clamp and Piston on the Sideplate of a Model "G" unit.
75. Washer (Stainless Steel)
Used with #2500 Screw against the Body Assembly to fasten the Back Plate Block to the Body Assembly.
77. Piston Assembly
(White Plastic) Two are needed for the Remote Control unit, only one is needed for the Aquabot Turbo Solo. This also goes for the Aquamax RC/Solo units. The T4 requires two.
111. Socket Assembly - Aquabot Turbo Solo/RC/Aquamax Bi-Turbo
4-pin, male, 4-wire Always unplug unit before working on electrical system!
111. Socket Assy.
7-Pin Male, 7-Wire. For use with Aquabot T4, All Aquamax RC Units, Old Aquabot Plus RC/Ultra112. Fuse Holder
Standard, push and turn style. Always unplug unit before working on electrical system!
114. Lighted Switch (For most power supplies)
Standard Red, 3-wire. Always unplug unit before working on electrical system.
114. Lighted Switch for Power Supplies with Adjustable Timer
Thin Red, 3-wire. Always unplug unit before working on electrical system.
116. TRANSMITTER FOR AQUABOT PLUS RC\ULTRA
Radio RC, Grey & Yellow with Blue Buttons and Red LED light118. Cord for Power Supply
3-wire, Green, Black and White. For all power supplies. Always unplug unit before working on electrical system!
119. TIMER 7 HOUR INTERNAL FIXED
Internal Fixed timer, 120 V, used on the Aquabot Turbo, Solo and RC.
119. OUTDOOR TIMER
8-hour, Programmable, GFCI - Used to regulate cleaner's run time when it does not have an auto shut-off.