- POOL CLEANERS/PARTS
- WATER TESTING
- PALINTEST LUMISO POOLTEST EXPERT PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST 6 PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST 3 PHOTOMETER AND REAGENTS
- PALINTEST POOLTEST 10 PREMIER PHOTOMETER AND REAGENTS
- PALINTEST POOLTEST 25 PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST PHOTOMETERS
- PALINTEST DRINKING WATER, WASTE WASTER AND PROCESS WATER TESTING
- PALINTEST COOL POOLTESTER AND REAGENTS
- PALINTEST COMPARATOR KITS
- PALINTEST POOLTESTER KITS
- PALINTEST TEST STRIPS
- AUTOMATION/ SENSORS
- CHEMICALS
- CHLORINE GENERATORS
- PUMPS & FILTERS
- FILTER CARTRIDGES
- TOOLS & ACCESSORIES
- CHEMICAL FEEDERS
- POOL LIGHTS
- POOL COVERS
- ALARMS
- ALADDIN PRODUCTS
AQUABOT ULTRA PARTS
:
from
to
Sort by:Recommended
- For use with the Aquabot Ultra, Aquamax, Aquamax Bi-Turbo, Ultramax Junior, JetMax
101. Filter Bag (Mesh)
For use with the Aquabot Ultra, Aquamax, Aquamax BiTurbo, Ultramax Junior, JetMax57. Drive Belts (per pair)
Tan belts. If you are changes your drive belts, we also suggest replacing your #51-Bushings and inspect your #58-Drive Pulley for wear. Any wear in these items can cause slack in your drive belts and reduce their longevity. We also suggest installing a belt tensioner device to take up any slack in your belts.
56. Stepped Sleeve Roller
Beige Supports Drive Belts, installs on the upper Sideplate leg. In 2004, Aqua Products switched to the Beige Stepped Sleeve Roller, which is slightly thicker than the white ones. This change helps the belts stay tighter, which helps prevent abnormal wear. If you have an older unit we suggest upgrading to the beige rollers. Each unit has 2 #56. Stepped Sleeve Rollers.
Foam Climbing Rings (Set of 4)
Light Blue PVA (1" thick)The climbing rings slide over the standard brushes and give the unit more traction for climbing slick surfaces.99. Drive Track with Traction Tabs (Blue)
Used for all Model "G" units. Must use spacer brackets for RC and T4 units.45. Sideplate
Blue, 6 holes, 4 for bolts, 2 for motor access. For AB Plus RC, AB Ultra, AMAX, AMAX Biturbo, Ultramax JR, UMAX97. Brushes - (Blue Molded Rubber Brush, cut in half)(set of 4)
Used on the Aquabot Ultra and the Ultramax Jr.97. Brushes - Light Blue PVA Foam (Set of 4)
Used on the Aquabot Ultra and Ultramax Jr.This is a long lasting brush that provides excellent traction. They can be a little difficult to install.12. P-Clip (5/8", Coated Steel)
Used to fasten the insulated part of a 4, 7 or 9-wire cable to the Handle Assembly.12. P-Clip (11/16", Stainless Steel)
Used to fasten the foam-insulated part of a 9-wire cable to the Handle Assembly.12. P-Clip (11/16", Plastic)
Used to fasten the foam-insulated part of a 9-wire cable to the Handle Assembly. (We suggest the stainless steel P-Clip)13., 74. or 81. Screw (#8, 11/16", Phil Pan-Flat Head.
Used to attach the side plate to the body assembly. On the T4, used to fasten the clamps around the DC pump to the Plate Block. On the T2, used to fasten drive motor to the body assembly.
17. Cable Assembly (7-wire, 75 feet, Floating)
Used on Aquabot Plus RC and Aquabot Ultra. Always unplug unit before working on electrical system.
30. or 74. Lock-Nuts Set of 8
Hex, Nylon Insert. For fastening the screws of the Anti-Roll Brackets. On the T4, used to attach screws of the Clamp and attach it to the Sideplate.
60. Pump Motor
For the Aquabot Plus RC, AB Ultra, Aquamax Jr. Plus, Aquamax, Aquamax B-Turbo, Ultramax Jr. and Ultramax.Pump motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.75. Washer (Stainless Steel)
Used with #2500 Screw against the Body Assembly to fasten the Back Plate Block to the Body Assembly.
79. Junction Box Assembly
Connections: 7-pin Cable Assembly, 2-Wire Pump, 2-Drive Motor Connections. Non-Returnable.79. Junction Box Assembly
Connections: 7-Pin Cable, 1 Pump, 1 Light, 2 Drive Connections. For Aquabot Ultra Lumina.79. Junction Box Assembly
Connections: 7-Pin Cable, 1 Pump, 2 IR, 2 Drive Connections. For Aquabot Ultra Infra-Red.80. Drive Motor (MASTER, black)
For Aquabot Plus RC and Aquabot Ultra. Drive motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.83. Spiral Pin
3/4" long stainless steel. Used in the end of the Drive Motor shaft, use Lok-Tite when installing.
96. Screw (Small used to fasten wheeltube brace to body)
For Aquabot Plus RC, Aquabot Ultra and Ultramax Jr.104. Screw (#6, 11/16", Phil Pan-Flat Head, Pointed)
Used to fasten the 5300/5301 Filter Screen to the Body Assembly.
106., 107. Intake Valve Flap
Black PVC Rubber. For use with Aquabot Ultra, Aquamax, Aquamax BiTurbo, JetMax111. Socket Assy.
7-Pin Male, 7-Wire. For use with Aquabot T4, All Aquamax RC Units, Old Aquabot Plus RC/Ultra112. Fuse Holder
Standard, push and turn style. Always unplug unit before working on electrical system!
114. Lighted Switch (For most power supplies)
Standard Red, 3-wire. Always unplug unit before working on electrical system.
Main Drain Bumper
Snaps into place on main drain grate - keeps unit from getting stuck on main drain.
- Free shipping
101. Choose Any Two Filter Bags (All Purpose or Leaf Bag) w/ Free Shipping
Pick any two Filter Bags with Free Shipping (one of each or two of the same). Choose between the standard 2 micron filter bag. Or the leaf filter bag (picks up larger debris without restricting the water flow.) Fits all residential Aquabot and Watertech units
List which two bag you would like in the CUSTOMER NOTES section during checkout.
- Standard 2 Micron (8111)
- Leaf & Large Debris Bag (8112)
101. Filter Bag (Fine)(All Purpose)
This is the standard 2 micron filter bag. Fits all residential Aquabot and Watertech units
101. Filter Bag (Mesh)(Leaf Bag)
This filter bag is used when there are a lot of leaves in the pool. It has larger holes in the bag that allow the unit to suck up larger debris without restricting the flow. Fits all residential Aquabot and Watertech units