AQUABOT TURBO T PARTS

:

Clear
Clear
Clear all
Products: 1–31 of 31
Show:100
Sort by:Recommended
    • Free shipping

    101. Choose Any Two Filter Bags (All Purpose or Leaf Bag) w/ Free Shipping

    Pick any two Filter Bags with Free Shipping (one of each or two of the same). Choose between the standard 2 micron filter bag. Or the leaf filter bag (picks up larger debris without restricting the water flow.) Fits all residential Aquabot and Watertech units . . .asd

    List which two bag you would like in the CUSTOMER NOTES section during checkout. 

    • Standard 2 Micron (8111)
    •  Leaf & Large Debris Bag (8112)

     

    • $97.94

  • 57. Drive Belts (per pair)

    Tan belts. If you are changes your drive belts, we also suggest replacing your #51-Bushings and inspect your #58-Drive Pulley for wear. Any wear in these items can cause slack in your drive belts and reduce their longevity. We also suggest installing a belt tensioner device to take up any slack in your belts.

    • $19.99

  • Aquabot - Drive Belts & Bushings

    Aquabot Parst Kit - Drive Belt & Bushings

    • $44.72

  • 101. Filter Bag (Fine)(All Purpose)

    This is the standard 2 micron filter bag. Fits all residential Aquabot and Watertech units

    • $49.95

  • 101. Filter Bag (Mesh)(Leaf Bag)

    This filter bag is used when there are a lot of leaves in the pool. It has larger holes in the bag that allow the unit to suck up larger debris without restricting the flow. Fits all residential Aquabot and Watertech units
    • $46.75

  • Power Supply Male Adaptor from 3-pin to 2-pin

    A900004 - To adapt the 2-pin socket to the floating cable with 3-pin female plug. 

    • $39.98

  • 51. Bushing

    White Plastic, 1/2" Hole, 2 notches.

    • $4.95

  • 1. HANDLE ASSEMBLY

    Bright White, Bracket Included
    • $103.88

  • 2. HANDLE BRACKET

    Bright White
    • $34.85

  • 99. Drive Track with Traction Tabs (Blue)

    Used for all Model "G" units. Must use spacer brackets for RC and T4 units.
    • $23.35

  • 91. Retaining Ring

    Stainless Steel "E" Clip
    • $4.99

  • 61. Propeller

    All Units.

    • $14.95

  • 58. Pulley Assembly (Medium)

    Used on all Black Drive Motors. Approximately 2.75-inches long.
    • $33.81

  • 45. SIDEPLATE

    Bright White, no holes
    • $27.88

  • 8. Screw

    10-32, 7/8" Phil Pan Head

    • $1.27

  • 9., 48. Screw (#8, 11/16", Phil Pan Head)

    Used for side plate on Older units.

    • $1.27

  • 13., 74. or 81. Screw (#8, 11/16", Phil Pan-Flat Head.

    Used to attach the side plate to the body assembly. On the T4, used to fasten the clamps around the DC pump to the Plate Block. On the T2, used to fasten drive motor to the body assembly.

    • $1.27

  • 17. CABLE ASSEMBLY

    2-Wire, 60 Feet, Floating **Floating Cable is a non-returnable item and should be installed by a Factory Authorized Service Center.
    • $281.75

  • 26. BODY ASSEMBLY

    Blue, with Lock Tabs, Pin, Outlet Ring and Inserts.
    • $138.65

  • 36. LOCK-TABS (SET OF 2)

    Natural Plastics - For all Body Assemblies, used to hold Bottom Lids to base of the cleaner.

    • $7.96

  • 40. Grommet (Rubber)

    Use around cable assembly on Body. Used on Turbo T, T2, T4 and ThunderJet units.

    • $2.44

  • 52. Bushing for Pin Support

    White Plastic, 1/4" Hole, 2 notches.

    • $4.66

  • 55. Large Roller

    White, Plastic. Supports the Drive Track, installs on Body's Pin support. (Non drive belt side of unit)
    • $9.31

  • 56. Stepped Sleeve Roller

    Beige Supports Drive Belts, installs on the upper Sideplate leg. In 2004, Aqua Products switched to the Beige Stepped Sleeve Roller, which is slightly thicker than the white ones. This change helps the belts stay tighter, which helps prevent abnormal wear. If you have an older unit we suggest upgrading to the beige rollers. Each unit has 2 #56. Stepped Sleeve Rollers.

    • $2.90

  • 80. DRIVE MOTOR FOR AQUABOT TURBO T

    Blue with bare wire leads.Pump motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.
    • $320.85

  • 87. SHRINK TUBE - 1/2" PER FOOT

    Used to seal 2-wire connections, use over heat shrink SP1617
    • $11.66

  • 88. SHRINK TUBE - 3/4" PER FOOT

    Used to seal all medium sized connections at Junction Box.
    • $11.66

  • 90. Wheel Tube Assembly - Model "G"

    This wheel tube is for units that run the "G" track. The "G" track has the traction tabs coming out from the track. See #99 for detail of "G" track.
    • $69.94

  • 103. FILTER SCREEN

    Blue, rounded cage.
    • $27.88

  • 106. INTAKE VALVE FLAP

    Blue Plastic
    • $4.60