AQUABOT T4 VERSION 2004-2005 PARTS

Pick any two Filter Bags with Free Shipping (one of each or two of the same). Choose between the standard 2 micron filter bag. Or the leaf filter bag (picks up larger debris without restricting the water flow.) Fits all residential Aquabot and Watertech units . . .asd

List which two bag you would like in the CUSTOMER NOTES section during checkout. 

• Standard 2 Micron (8111)
•  Leaf & Large Debris Bag (8112)

Tan belts. If you are changes your drive belts, we also suggest replacing your #51-Bushings and inspect your #58-Drive Pulley for wear. Any wear in these items can cause slack in your drive belts and reduce their longevity. We also suggest installing a belt tensioner device to take up any slack in your belts.

Aquabot Parst Kit - Drive Belt & Bushings

This is the standard 2 micron filter bag. Fits all residential Aquabot and Watertech units

White, Plastic. For use with the Aquabot

Round Head, hole in end.

Beige Supports Drive Belts, installs on the upper Sideplate leg. In 2004, Aqua Products switched to the Beige Stepped Sleeve Roller, which is slightly thicker than the white ones. This change helps the belts stay tighter, which helps prevent abnormal wear. If you have an older unit we suggest upgrading to the beige rollers. Each unit has 2 #56. Stepped Sleeve Rollers.

All Units.

Use between Handle Bracket and Cotter Ring inside most Handle Assemblies 

Use to fasten Clevis Pin inside the Handle Bracket of most units.

Aluminum, 3/16"  

10-32, 7/8" Phil Pan Head

Used for side plate on Older units.

For fastening the foam-insulated part of a 2-wire cable to the Body Assembly.

Used to attach the side plate to the body assembly. On the T4, used to fasten the clamps around the DC pump to the Plate Block. On the T2, used to fasten drive motor to the body assembly.

For end of Cable Assembly. Always Disconnect power before working on the electrical system!

Helps to take the curls out of the power cord.

Uses 7-pin Plug/Socket. For Aquabot T4.

For Aquabot T2 and T4.

Hex, Nylon Insert. For fastening the screws of the Anti-Roll Brackets. On the T4, used to attach screws of the Clamp and attach it to the Sideplate.

Outer housing  for all Jet and Rover Units and Screen

For Center Wheel on Jet and Rover Units. - Free Moving bracket for small black wheel.

Used to fasten the Lock-Tabs to the Body Assembly.

Used to fasten the Screws of the Lock-Tabs to the Body Assembly.

Used around the Cable Assembly on the Body Assembly. For AquaJet, JetMax and Pool Rover Units.

Use around cable assembly on Body. Used on Turbo T, T2, T4 and ThunderJet units.

Pump-Motor-A6005-03, S1A6014 

Plastic, cylinder used between Plate Block and Body Assembly. Used on Aquabot Turbo Solo, Aquabot Turbo RC, AquabotT4 and all Aquamax RC/Solo Units.

Used to fasten Clamp & Piston on the Sideplate of a standard unit.

Used to fasten Clamp and Piston on the Sideplate of a Model "G" unit.

Used with #2500 Screw against the Body Assembly to fasten the Back Plate Block to the Body Assembly.

(White Plastic) Two are needed for the Remote Control unit, only one is needed for the Aquabot Turbo Solo. This also goes for the Aquamax RC/Solo units. The T4 requires two.

3/4" long stainless steel. Used in the end of the Drive Motor shaft, use Lok-Tite when installing.

Standard, push and turn style. Always unplug unit before working on electrical system!

Black plastic, with screws, nuts and star washers.

Front Digital Display, 1-7 Hours Adjustable

Snaps into place on main drain grate - keeps unit from getting stuck on main drain.