- POOL CLEANERS/PARTS
- WATER TESTING
- PALINTEST LUMISO POOLTEST EXPERT PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST 6 PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST 3 PHOTOMETER AND REAGENTS
- PALINTEST POOLTEST 10 PREMIER PHOTOMETER AND REAGENTS
- PALINTEST POOLTEST 25 PHOTOMETER AND REAGENTS
- PALINTEST LUMISO POOLTEST PHOTOMETERS
- PALINTEST DRINKING WATER, WASTE WASTER AND PROCESS WATER TESTING
- PALINTEST COOL POOLTESTER AND REAGENTS
- PALINTEST COMPARATOR KITS
- PALINTEST POOLTESTER KITS
- PALINTEST TEST STRIPS
- AUTOMATION/ SENSORS
- CHEMICALS
- CHLORINE GENERATORS
- PUMPS & FILTERS
- FILTER CARTRIDGES
- TOOLS & ACCESSORIES
- CHEMICAL FEEDERS
- POOL LIGHTS
- POOL COVERS
- ALARMS
- ALADDIN PRODUCTS
JETMAX JUNIOR PARTS
:
from
to
Clear
Clear
Sort by:Recommended
12. P-Clip (3/8" Plastic)
For fastening the foam-insulated part of a 2-wire cable to the Body Assembly.
15. Plug (3-Pin, Female, 2-wire)
For end of Cable Assembly. Always Disconnect power before working on the electrical system!
17. Cable Assembly. (2-wire, 75 feet, Floating)
For the Aquabot Plus and Aquamax Jr. HT. Always Disconnect power before working on the electrical system!27., 62. Screw (8-18, 3/4", Phil No-Head
Used to fasten the Pump Motor to the Outlet Bottom Ring on the Body Assembly.32. Extension Bracket (Black)
For Jet Valve - Pool Rover Jr./Plus, Aquajet, ThunderJet IG/ JetMax. 5-Holes for Jet Valve34. Valve Lock (White, Delrin Plastic for Flap)
For inside of Jet Valve housing of all Jet/Rover units.40. Grommet (Rubber)
Used around the Cable Assembly on the Body Assembly. For AquaJet, JetMax and Pool Rover Units.
41. Foam Block (w/ slot & bracket, 4" square float)
Used on Pool Rover Plus, AquaJet, ThunderJet IG and JetMax.53. Small Wheel
Black, For under sideplate. For use with Pool Rover Plus, ThunderJet IG, AquaJet, JetMax
59. Washer (Delrin, For between wheels/side plate of movable axle)
Used on the T2, T4, Pool Rover, ThunderJet AG and JetMax.60. PUMP MOTOR FOR JETMAX
Pump motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.65. Tubing (Clear PVC, 5/16" IDx1/2" OD) (per foot)
For T2, T4, Pool Rover Plus, ThunderJet IG, AquaJet and JetMax90. Wheel Assembly (Black Rubber, 6")
Used on the Pool Rover Jr., Pool Rover Plus, ThunderJet IG, AquaJet and the JetMax.93. Tube (Black Plastic, 3" Oval, 12" long)
For the Pool Rover, Pool Rover Plus, ThunderJet AG/IG, AquaJet.94. Axle (Fiberglass, 16.5"x1/2" OD, Front & Rear)
Used on the Pool Rover Jr., ThunderJet AG/IG, AquaJet96. Lanyard (Black Plastic)
Used to tie onto Clevis pin, attached to Tube or Body. Used on all Jet and Rover Units.101. Filter Bag (Mesh)(Leaf Bag)
This filter bag is used when there are a lot of leaves in the pool. It has larger holes in the bag that allow the unit to suck up larger debris without restricting the flow. Fits all residential Aquabot and Watertech units106. INTAKE VALVE FLAP (BLUE PLASTIC)
Used on the Aquabot, Aquabot Turbo, Solo/RC, Storm, Tempo & T4.108. H-Float
Foam, Plastic and screws. This float gets fastened to bottom lid if cleaner is not climbing the wall high enough.
109. Side Pocket Floats (Pair)
White Foam Blocks. These are inserted into the bottom lid if the unit is not climbing high enough. (The H-Float must be installed in order to install the Side Pocket Floats)
111. Socket Assembly
(3-pin, male, 2-wire) Aquabot, Turbo, Storm, Tempo, Turbo T, T2 Always unplug unit before working on electrical system!
114. Lighted Switch for Power Supplies with Adjustable Timer
Thin Red, 3-wire. Always unplug unit before working on electrical system.
119. TIMER - 60 SECOND
Front Dial, 2-hour Automatic Shut-Off, No Reset Switch - For Pool Rover/Junior and ThunderJet AG