• Now AcceptingPayPal

AQUAMAX JUNIOR HT/JUNIOR PLUS PARTS

Products: 1–80 of 80
Show:100
Sort by:Recommended

  • 1. Handle Assembly

    Blue & White, Bracket Included.
    • $103.88

  • 2. Bracket for Handle (Blue)

    Bracket fo Handle (Blue)

    • $34.85

  • 4. Clevis Pin

    Round Head, hole in end.

    • $2.86

  • Washer

    Use between Handle Bracket and Cotter Ring inside most Handle Assemblies 

    • $0.83

  • Cotter Ring

    Use to fasten Clevis Pin inside the Handle Bracket of most units.

    Aluminum, 3/16"  

    • $0.83

  • 8. Screw

    10-32, 7/8" Phil Pan Head

    • $1.27

  • 12. P-Clip (1/4" Plastic)

    For fastening the non-foam-insulated part of a 2-wire cable to the Body Assembly.

    • $1.27

  • 12. P-Clip (3/8" Plastic)

    For fastening the foam-insulated part of a 2-wire cable to the Body Assembly.

    • $1.27

  • 12. P-Clip (7/16", Plastic)

    Used to fasten the foam insulated part of a 2-wire cable to the Handle Assembly.

    • $1.27

  • 12. P-Clip (1/2", Plastic)

    Used to fasten the Heat Shrink part of the 2-wire cable to the Handle Assembly.

    • $1.27

  • 12. P-Clip (9/16", Plastic)

    Used to fasten the heat shrink part of the 2-wire cable to the Handle Assembly.

    • $1.27

  • 12. P-Clip (5/8", Coated Steel)

    Used to fasten the insulated part of a 4, 7 or 9-wire cable to the Handle Assembly.
    • $2.44

  • 13., 74. or 81. Screw (#8, 11/16", Phil Pan-Flat Head.

    Used to attach the side plate to the body assembly. On the T4, used to fasten the clamps around the DC pump to the Plate Block. On the T2, used to fasten drive motor to the body assembly.

    • $1.27

  • 15. Plug (3-Pin, Female, 2-wire)

    For end of Cable Assembly. Always Disconnect power before working on the electrical system!

    • $14.63

  • 15. Plug (4-Pin, Female, 4-wire)

    For end of Cable Assembly for Aquabot Turbo Solo, Aquabot Turbo RC. Always Disconnect power before working on the electrical system!

    • $45.79

  • 16. EZ-Swivel (For 2 wire Cable)

    Helps to take the curls out of the power cord.

    • $29.99

  • 16. EZ-SWIVEL

    For 5 and 7 wire cables.
    • $46.62

  • 17. Cable Assembly. (2-wire, 75 feet, Floating)

    For the Aquabot Plus and Aquamax Jr. HT. Always Disconnect power before working on the electrical system!
    • $353.03

  • 17. Cable Assembly (2-wire, 100 feet, Floating)

    For Aquamax Junior Plus and Jet Max.
    • $507.84

  • 17. Cable Assembly (7-wire, 120 feet, Floating)

    For Aquamax Jr. Plus RC and Aquamax B-Turbo RC.
    • $737.13

  • 25. Outlet Top

    Top and bottom, glue ring to Body Assembly with PVC Glue.

    • $30.32

  • 26. Body Assembly

    White with Holes, Lock Tabs, Pin, Outlet Ring and Inserts.
    • $138.65

  • 26. Body Assembly

    White with holes, Lock Tabs, Pin, Outlet Ring and Inserts.
    • $138.65

  • 27., 62. Screw (8-18, 3/4", Phil No-Head

    Used to fasten the Pump Motor to the Outlet Bottom Ring on the Body Assembly.
    • $1.27

  • 29. Anti-Roll Brackets

    Plastic, White. Not required on most units. Set of 4.

    • $11.77

  • 30. or 74. Lock-Nuts Set of 8

    Hex, Nylon Insert. For fastening the screws of the Anti-Roll Brackets. On the T4, used to attach screws of the Clamp and attach it to the Sideplate.

    • $1.33

  • 31. Screw (M-5), Phil Bevel Head

    To fasten the Anti-Roll Brackets to the Body Assembly.
    • $1.27

  • 38. Screws (18-8, 8/32"x1/2", Phil-Bev Head)

    Used to fasten the Lock-Tabs to the Body Assembly.

    • $1.27

  • 39. Lock-Nut (Nylon Insert, Hex)

    Used to fasten the Screws of the Lock-Tabs to the Body Assembly.

    • $0.83

  • 45. Sideplate

    Blue, 4 holes for bolts. For use with Aquamax Junior HT, Aquamax Junior Plus
    • $28.60

  • 49. Screw

    Bolts, Long, For Sideplate.
    • $1.19

  • 51. Bushing

    White Plastic, 1/2" Hole, 2 notches.

    • $4.95

  • 52. Bushing for Pin Support

    White Plastic, 1/4" Hole, 2 notches.

    • $4.66

  • 54. Small Roller

    White plastic. Supports the Drive Track, install on lower legs of the Sideplate.
    • $2.76

  • 55. Large Roller

    White, Plastic. Supports the Drive Track, installs on Body's Pin support. (Non drive belt side of unit)
    • $9.31

  • 56. Stepped Sleeve Roller

    Beige Supports Drive Belts, installs on the upper Sideplate leg. In 2004, Aqua Products switched to the Beige Stepped Sleeve Roller, which is slightly thicker than the white ones. This change helps the belts stay tighter, which helps prevent abnormal wear. If you have an older unit we suggest upgrading to the beige rollers. Each unit has 2 #56. Stepped Sleeve Rollers.

    • $2.90

  • 57. Drive Belts (per pair)

    Tan belts. If you are changes your drive belts, we also suggest replacing your #51-Bushings and inspect your #58-Drive Pulley for wear. Any wear in these items can cause slack in your drive belts and reduce their longevity. We also suggest installing a belt tensioner device to take up any slack in your belts.

    • $19.99

  • 58. Pulley Assembly (Short)

    For use on the Aquabot, Aquabot Turbo, Aquabot Turbo Solo, Aquabot Turbo RC, Storm and Tempo.
    • $27.98

  • 58. Pulley Assembly (Medium)

    Used on all Black Drive Motors. Approximately 2.75-inches long.
    • $33.81

  • 60. Pump Motor (Aquabot Turbo, Solo and Remote Control) NO WARRANTY

    Also used in the Aquamax Jr. HT. Pump motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.
    • $229.79

  • 60. Pump Motor

    For the Aquabot Plus RC, AB Ultra, Aquamax Jr. Plus, Aquamax, Aquamax B-Turbo, Ultramax Jr. and Ultramax. Pump motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.
    • $282.74

  • 61. Propeller

    All Units.

    • $14.95

  • 73. Screw (10-32, 1-3/4" Phil Pan Head)

    Used to fasten Clamp & Piston on the Sideplate of a standard unit.

    • $1.27

  • 73. Screw (10-32, 1-3/4" Phil Pan Head)

    Used to fasten Clamp and Piston on the Sideplate of a Model "G" unit.

    • $1.27

  • 75. Washer (Stainless Steel)

    Used with #2500 Screw against the Body Assembly to fasten the Back Plate Block to the Body Assembly.

    • $0.95

  • 80. Drive Motor - Aquabot Turbo/Aquamax Jr. HT NO WARRANTY

    White with Terminal Basin. Drive motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.

    • $355.40

  • 80. Drive Motor (White with Terminal Basin)

    Drive motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system. For Aquamax Jr. Plus
    • $349.14

  • 80. Drive Motor (Black with bare wire leads)

    Drive motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system. For Aquamax Jr. Plus IR, Aquamax IR, Aquamax Bi-Turbo IR.
    • $422.21

  • 80. Drive Motor (Black with bare wire leads)

    For Aquamax, Aquamax Bi-Turbo, Aquamax RC, Aquamax Bi-Turbo RC. Drive motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.
    • $422.21

  • 80. Drive Motor for Aquamax Junior Plus Solo

    (Black with bare wire leads) Drive motor comes with a 6 month factory warranty if it is installed by a factory authorized repair center. (Aqua Service Distributors is a factory authorized repair center.) If the motor is not installed by an authorized service center there is not warranty and the the motor cannot be returned. Always disconnect the power before working on the electrical system.
    • $422.21

  • 81. Loop Connector (pair)

    Aluminum, Crimp. For attaching bare motor wires to Brass Terminals.

    • $1.27

  • 82. Brass Nuts

    Hex, Small. For fastening the Loop Connectors of wires around the brass motor terminals.

    • $1.27

  • 83. Spiral Pin

    3/4" long stainless steel. Used in the end of the Drive Motor shaft, use Lok-Tite when installing.

    • $4.27

  • 84. Terminal Cover

    Plastic, rectangular. Used to seal up terminal basin in drive motors.

    • $2.44

  • 85. Screw (5/8")

    Used for sealing the terminal cover onto the terminal basin of white drive motors. (HAND-TIGHTEN ONLY)

    • $1.27

  • 86. Shrinkable Butt Connectors (pair)

    Light Blue, crimp closed and head shrink to seal.
    • $2.54

  • 87. SHRINK TUBE - 1/2" PER FOOT

    Used to seal 2-wire connections, use over heat shrink SP1617
    • $11.66

  • 90. Wheel Tube Assembly - Model "G"

    This wheel tube is for units that run the "G" track. The "G" track has the traction tabs coming out from the track. See #99 for detail of "G" track.
    • $69.94

  • 91. Retaining Ring

    Stainless Steel "E" Clip
    • $4.99

  • 92. Washer (Nylon, Flat)

    Used on all units within wheel or wheel tube.

    • $1.39

  • 97. Brushes (Blue Molded Rubber)(Pair)

    This is the standard brush and can be used on all types of pools.
    • $81.79

  • 97. Brushes (Light Blue PVA Foam)(Pair)

    The PVA foam brushes last longer than the standard brushes, but are more expensive. The PVA foam brushes have more traction when compared to the standard brush so the unit travels faster and will climb the walls higher (floats may have to be adjusted if changing from molded rubber brushes). The PVA brushes are more difficult to install and detailed instructions will need to be followed. You can find these instructions on our "Do-it-Yourself" page of this website.
    • $74.99

  • 99. Drive Track with Traction Tabs (Blue)

    Used for all Model "G" units. Must use spacer brackets for RC and T4 units.
    • $23.35

  • 99. Drive Track (Blue)(each)

    Used for all units.
    • $22.24

  • 101. Filter Bag (Mesh)(Leaf Bag)

    This filter bag is used when there are a lot of leaves in the pool. It has larger holes in the bag that allow the unit to suck up larger debris without restricting the flow. Fits all residential Aquabot and Watertech units
    • $46.75

  • 103. Filter Screen

    White Cage around motors.
    • $27.88

  • 104. Screw (#6, 11/16", Phil Pan-Flat Head, Pointed)

    Used to fasten the 5300/5301 Filter Screen to the Body Assembly.

    • $1.27

  • 105.. Bottom Lid Assembly

    (White, W-Shape Wire Frame)

    • $101.61

  • 106. INTAKE VALVE FLAP (BLUE PLASTIC)

    Used on the Aquabot, Aquabot Turbo, Solo/RC, Storm, Tempo & T4.
    • $4.99

  • 108. H-Float

    Foam, Plastic and screws. This float gets fastened to bottom lid if cleaner is not climbing the wall high enough.

    • $14.68

  • 109. Side Pocket Floats (Pair)

    White Foam Blocks. These are inserted into the bottom lid if the unit is not climbing high enough. (The H-Float must be installed in order to install the Side Pocket Floats)

    • $3.71

  • 110. Power Supply

    3-Prong Male Socket. For use with Aquamax Jr HT, Aquamax Jr. Plus, Aquamax.
    • $232.44

  • 110. Power Supply

    4-Prong Male Socket. For use with Aquamax Junior Plus RC, Aquamax RC
    • $355.16

  • 111. Socket Assembly

    (3-pin, male, 2-wire) Aquabot, Turbo, Storm, Tempo, Turbo T, T2 Always unplug unit before working on electrical system!

    • $10.49

  • 112. Fuse Holder

    Standard, push and turn style. Always unplug unit before working on electrical system!

    • $8.14

  • 112. Fuse Holder (Phillips Head Style)

    (Phillips Head Style)
    • $8.14

  • 114. Lighted Switch (For most power supplies)

    Standard Red, 3-wire. Always unplug unit before working on electrical system.

    • $8.16

  • 115. Antenna

    4", with hardware. Should only be installed by a certified technician.
    • $11.66

  • Foam Climbing Rings (Set of 4)

    Light Blue PVA (1" thick) The climbing rings slide over the standard brushes and give the unit more traction for climbing slick surfaces.
    • $26.71